Strategy·5 min read

Haulage Associations and Truckmakers Just Joined Forces on EU Weight Rules: What the Payload Fight Means for Your Next Truck Order

Eleven European haulage associations and truck manufacturer group ACEA have both pushed Brussels in the past two weeks to finally settle the EU Weights and Dimensions Directive, the file that decides how much payload electric and hydrogen trucks can actually carry.

FleetlySolutions · 9 November 2026

A Rare Show of Unity Before the 30 November Council Meeting

On 26 October, eleven road haulage associations from Germany, France, Denmark, Norway, Sweden, Finland, the Netherlands, Belgium and Ireland did something unusual. They issued a joint statement in Brussels calling on EU member states and the European Parliament to reach an agreement on the revision of Directive 96/53/EC without further delay.

Three days later, the truck manufacturers' side added its own pressure. The European Automobile Manufacturers' Association renewed its call on 29 October for an "ambitious" agreement on the revision of the EU Weights and Dimensions Directive, arguing that the rules must compensate adequately for the additional weight of zero-emission powertrains if operators are to adopt them without sacrificing payload. Both appeals came ahead of the Transport Council meeting on 30 November 2026, with the aim reportedly being to conclude negotiations by the end of the year, during Ireland's presidency of the Council of the EU.

What's Actually Changing: The 44-Tonne Question

The Commission tabled this proposal back in July 2023 as part of the Greening Transport Package, aiming to remove a structural disadvantage: battery and fuel-cell trucks weigh more than diesel equivalents, so under the old rules they lose cargo capacity just for using cleaner technology. The Council adopted its general approach on 3 December 2025, after more than two years of deadlock, finally clearing the way for trilogue talks.

The Council's position increases the weight allowance of some electric and hydrogen articulated trucks from two to four tonnes, meaning these trucks will be able to drive further on a single charge without compromising on the load they can carry. But the allowance isn't uniform. The compromise differentiates between five-axle vehicles, which get two extra tonnes, and six-axle vehicles, which get four, and environmental group Transport & Environment has argued that negotiators should raise the five-axle allowance to at least 2.5 tonnes. Zero-emission articulated trucks may also be up to 0.90 metres longer to make room for batteries and hydrogen tanks.

The Real Sticking Point: Drive-Axle Weight

Total gross weight isn't where this fight actually lives. Reports through 2026 pointed to a split between the Commission, which favoured raising the drive-axle limit to 12.5 tonnes, and a majority of member states seeking to retain the current 11.5-tonne limit, largely over concerns that heavier drive axles accelerate wear on roads and bridges.

ACEA has made the operational consequence explicit: a vehicle can be legal at 44 tonnes gross weight and still exceed its axle limit, which defeats the purpose of the extra allowance. The manufacturers' group says this particularly affects two-axle 4x2 tractor units, the configuration most widely used in long-haul operations, where the current direction of negotiations may leave insufficient weight allowance to actually use the extra tonnage without breaching axle rules.

More Reporting Is Coming Regardless of How This Ends

Whatever final number gets agreed on weight, one piece of the package looks set to stick: from 1 December 2029, zero-emission vehicles will need to transmit reliable weight data remotely through on-board mass monitoring equipment. ACEA has flagged this requirement, alongside new smart tachograph provisions, as a potential extra compliance burden that could work against the decarbonisation goal the directive is meant to support.

Separately, the European Shippers' Council has called for caution around on-board mass monitoring, specifically to ensure a level playing field between EU-registered vehicles and non-EU trucks operating on the same routes. That's a detail worth watching if you run cross-border lanes into or out of the EU.

Where This Leaves Fleet Managers Right Now

Nothing here is law yet. The first trilogue took place on 9 December 2025 and the legislative procedure remains open as associations push for a close before year end. Given that this file has already run more than two years past its original July 2023 proposal date, a 30 November deadline is an ambition, not a guarantee.

The practical takeaway for anyone weighing an electric or hydrogen truck order over the next 12 to 18 months is to avoid building your payload and total-cost-of-ownership case around the most favourable possible outcome. Model your route economics against the current 11.5-tonne axle limit and the two-tonne allowance for five-axle combinations, and treat anything above that as upside rather than a planning assumption.

How FleetlySolutions Fits Into This

This is exactly the kind of regulatory uncertainty our per-kilometre pricing engine is built to absorb. Because FleetlySolutions runs your freight pricing and route planning without tying it to a fixed vehicle spec, you can run parallel scenarios today, comparing diesel payload against a conservative and an optimistic ZEV weight allowance, and see the real cost-per-tonne-kilometre difference before you commit capital to a truck order.

The same route and toll planning layer that keeps you clear of current axle and bridge restrictions will simply absorb the new limits once they're finalised, without needing new hardware or a system migration. For a fleet manager trying to time an electric truck purchase against a moving regulatory target, that flexibility matters more than any single number coming out of Brussels on 30 November.

Put this into practice

See how FleetlySolutions plans, prices and audits your loads. Book a 20-minute demo.